kitswhe.blogg.se - Huawei E173 Firmware Update

#HUAWEI E173 FIRMWARE UPDATE INSTALL#

After a few seconds, you will receive a text message to your designated mobile number with the message Createlabz test.$ echo "Createlabz test" | sudo gammu sendsms TEXT ********** Replace ********** with the designated mobile number, you may also need to format it with the country code. Now you can send an SMS through the terminal by inputting this command.You can see the Gammu identify result like this.Now we will identify our dongle by input this command:.usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB2 usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB1 usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB0 (!!!!!GET THIS!!!!) option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2 option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1 option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0 You will notice multiple lines, get the latest mounted ttyUSB and replace it on the Gammu Configuration as indicated sample below.Note sometimes the Huawei E173 mount designation ttyUSB will change just input this command if you encountered some issues while running it.Select Yes to overwrite the configuration file.Set the settings as indicated, for the port may vary where your Huawei E173 ttyUSB is mounted, after setting it up select save.If a configuration file exists, Select Yes (For new Proceed to next):.Follow the pictures as instructed below, Use the arrow keys to change selection.

#HUAWEI E173 FIRMWARE UPDATE INSTALL#

Install the Gammu package by inputting this command.Now you can see it, then we will proceed to install the SMS Software.To save it press the CTRL+X key, then press the Y key, and press ENTER key to save.Then copy these and paste them on your terminal editor.For unsuccessful installation (Skip this if you see the Huawei E173 mounted to ttyUSB):.And input the command again, if not we will manually input it. If you don't see those in the terminal, try to disconnect and reconnect the device again. If you see it, proceed on to installing the SMS Software. Take note of the first line ttyUSB which is the ttyUSB0 we will be using later.usb 1-1.1.2: GSM modem (1-port) converter now attached to ttyUSB2 usb 1-1.1.2: GSM modem (1-port) converter now attached to ttyUSB1 usb 1-1.1.2: GSM modem (1-port) converter now attached to ttyUSB0 If you're successful you will see this in your terminal.

Check where's the Huawei E173 is mounted by inputting this command:.

$ sudo apt install ppp usb-modeswitch usb-modeswitch-data

Then install the required packages to run the Huawei E173 on the Raspberry Pi, input these following commands:.

It looks like this.īus 001 Device 008: ID 12d1:1436 Huawei Technologies Co., Ltd.

Next, look for your device in the list.

This command will list all USB devices connected. To do that open the Raspberry Pi terminal, then input the command below.

The first thing to do is to determine if the Huawei E173 is recognized by the Raspberry Pi.

Mount the Huawei E173 to Raspberry Pi like this. There's a multiple application of this, you can use the Raspberry Pi as monitoring of sensors, automate send and receive of SMS. So you can send or receive messages on your raspberry pi, or make an automated text. In this application, we will use the Huawei E173 as a USB modem to Raspberry Pi. It has a connection for an external antenna that can be useful in places with low mobile phone coverage. This modem is a widely used GSM/UMTS USB wireless modem. The Huawei HiLink E173 Cellular Modem is an ultra-slim device with a MicroSD card slot up to 32GB.